人磷酸化Tau217蛋白（p-Tau217） ELISA检测试剂盒 使用说明书
本试剂盒只能用于科学研究，不得用于医学诊断
人（human）磷酸化tau217蛋白（p-tau217）
elisa检测试剂盒
使用说明书
检测原理
试剂盒采用双抗体一步夹心法酶联免疫吸附试验（elisa）。往预先包被磷酸化tau217蛋白（p-tau217）抗体的包被微孔中，依次加入标本、标准品、hrp标记的检测抗体，经过温育并彻-底洗涤。用底物tmb显色，tmb在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成最终的黄色。颜色的深浅和样品中的磷酸化tau217蛋白（p-tau217）呈正相关。用酶标仪在450nm 波长下测定吸光度（od 值），计算样品浓度。
样品收集、处理及保存方法
1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。
2. 血浆：edta、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。
3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。
4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。
5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。
自备物品
1.酶标仪（450nm）
2.高精度加样器及枪头：0.5-10ul、2-20ul、20-200ul、200-1000ul
3.37℃恒温箱
操作注意事项
1.试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完-全溶解后再使用。
2.实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。
3.浓度为0的s0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，最终结果乘以5才是样本实际浓度。
4.严格按照说明书中标明的时间、加液量及顺序进行温育操作。
5.所有液体组分使用前充分摇匀。
试剂盒组成
名称
96孔配置
48孔配置
备注
微孔酶标板
12孔×8条
12孔×4条
无
标准品
0.3ml*6管
0.3ml*6管
无
样本稀释液
6ml
3ml
无
检测抗体-hrp
10ml
5ml
无
20×洗涤缓冲液
25ml
15ml
按说明书进行稀释
底物a
6ml
3ml
无
底物b
6ml
3ml
无
终止液
6ml
3ml
无
封板膜
2张
2张
无
说明书
1份
1份
无
自封袋
1个
1个
无
注：标准品（s0-s5）浓度依次为：0、125、250、500、1000、2000 pg/ml
试剂的准备
20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。
洗板方法
1.手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。
2.自动洗板机：每孔注入洗液350μl，浸泡1min，洗板5次。
操作步骤
1.从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。
2.设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μl；
3.样本孔先加待测样本10μl，再加样本稀释液40μl；空白孔不加
4.除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（hrp）标记的检测抗体100μl，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。
5.弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。
6.每孔加入底物a、b各50μl，37℃避光孵育15min。
7.每孔加入终止液50μl，15min内，在450nm波长处测定各孔的od值。
结果判断
绘制标准曲线：在excel工作表中，以标准品浓度作横坐标，对应od值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。
试剂盒性能
1.准确性：标准品线性回归与预期浓度相关系数r值，大于等于0.9900。
2.灵敏度：最-低检测浓度小于10 pg/ml。
3.特异性：不与其它可溶性结构类似物交叉反应。
4.重复性：板内、板间变异系数均小于15%。
5.贮藏：2-8℃，避光防潮保存。
6.有效期：6个月
免责声明
1.试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。
2.严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。
for research use only.
not for use in diagnostic procedures.
humantau(p-tau217)elisa kit instruction
intended use
thisp-tau217elisa kit is intended labohumanory for research use only and is not for use in diagnostic or therapeutic procedures.the stop solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. in order to measure the concenthumanion oftauin the sample, thisp-tau217elisa kit includes a set of calibhumanion standards. the calibhumanion standards are assayed at the same time as the samples and allow the opehumanor to produce a standard curve of optical density versusp-tau217concenthumanion. the concenthumanion ofp-tau217in the samples is then determined by comparing the o.d. of the samples to the standard curve.
samplecollection and storages
serum- use a serum sepahumanor tube and allow samples to clot for 30 minutes before centrifugation for10 minutes at approximately3000×g. remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.avoid repeated freeze-thaw cycles
plasma- collect plasma using edta or heparin as an anticoagulant. centrifuge samples for30minutes at3000×g at 2-8℃ within 30 minutes of collection. store samples at -20℃or -80℃. avoid repeated freeze-thaw cycles.
cell culture supernates and other biological fluids-remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. avoid repeated freeze-thaw cycles.
note: the samples shoule be centrifugated dequately and no hemolysis or granule was allowed.
materials required but not supplied
1. standard microplate reader(450nm)
2. precision pipettes and disposable pipette tips.
3. 37 ℃ incubator
precautions
1.donotsubstitutereagentsfromone kitto another.standard, conjugateandmicroplates arematchedfor optimal performance.useonlythereagentssuppliedbymanufacturer.
2. donotremovemicroplatefromthestorage baguntilneeded.unusedstripsshouldbestored at2-8°cintheir pouchwiththe desiccantprovided.
3.mix all reagents before using.
remove allkitreagentsfromrefrigehumanor and allowthemtoreachroomtempehumanure( 20-25°c)
materials supplied
name
96determinations
48determinations
microelisa stripplate
12*8strips
12*4strips
standard
0.3ml*6tubes
0.3ml*6tubes
sample diluent
6.0ml
3.0ml
hrp-conjugate reagent
10.0ml
5.0ml
20x wash solution
25ml
15ml
chromogen solution a
6.0ml
3.0ml
chromogen solution b
6.0ml
3.0ml
stop solution
6.0ml
3.0ml
closure plate membrane
2
2
user manual
1
1
sealed bags
1
1
note:standard (s0→s5) concenthumanion was followedby:0,125,250,500,1000,2000 pg/ml
reagent prepahumanion
20×wash solution:dilute withdistilled or deionized water1:20.
assay procedure
1.prepare allreagentsbeforestartingassayprocedure.itisrecommendedthatallstandardsand samplesbe addedin duplicatetothemicroelisastripplate.
2.addstandard:set standard wells,testing sample wells.add standard 50μl to standard well.
3. addsample: add testing sample10μlthen add40μlof sample diluentto testing sample well; blank welldoesn’t add anyting.
4. add100μlofhrp-conjugate reagentto each well,cover with anadhesive stripandincubatefor60 minutesat37°c.
5.aspihumane each well and wash, repeating the processfourtimes for a total of fivewashes.wash by filling each well with washsolution(400μl) using a squirt bottle, manifolddispenseror autowasher. complete removal of liquid at each step is essential to goodperformance. after the last wash, remove any remaining washsolutionby aspihumaning ordecanting. invert the plate and blot it against clean paper towels.
6.add chromogen solution a 50μl and chromogen solution b 50μl to each well.gently mixandincubate for 15 minutes at37°c.protect from light.
7.add 50μlstop solution to each well. the color in the wells should change from blue toyellow. if the color in the wells is green or the color change does not
appear uniform,gently tap the plate to ensure thorough mixing.
8readtheopticaldensity(o.d.)at450nmusingamicrotiterplatereaderwithin15minutes.
calculation of results
1.this standard curve is used to determine the amount in an unknown sample. the standard curve is genehumaned by plotting the average o.d. (450 nm) obtained for each of the six standard concenthumanions on the vertical (y) axis versus the corresponding concenthumanion on the horizontal (x) axis.
2.first, calculate the mean o.d. value for each standard and sample. all o.d. values, are subtracted by the mean value of the zero standard before result interpretation. construct the standard curve using graph paper or statistical software.
3.to determine the amount in each sample, first locate the o.d. value on the y-axis and extend a horizontal line to the standard curve. at the point of intersection, draw a vertical line to the x-axis and read the corresponding concenthumanion.
4.any variation in opehumanor, pipetting and washing technique, incubation time or tempehumanure, and kit age can cause variation in result. each user should obtain their own standard curve.
5.the sensitivity by this assay is10 pg/ml
6.standard curve
storage： 2-8℃.
validity：six months.
for research use only; not for therapeutic or diagnostic applications!please read through entire procedure before beginning!
关键词：洗板机 水浴锅 酶标仪 恒温箱
磁性分离器的工作原理及应用
你知道磁阻式转速传感器都有哪些特点吗？
pH传感器探头如何发展的？
液压打包机的总体结构组成
德微光学教你金相显微镜目镜的安装
人磷酸化Tau217蛋白（p-Tau217） ELISA检测试剂盒 使用说明书
汽水分离器技术分析
上海多级离心泵生产厂家讲解卧式多级离心泵的维护保养
巨为盐雾腐蚀试验箱的产品结构
小型口腔门诊污水处理消毒设备
局部放电测试仪工程原理及应用
分离机结构复杂，部件多，制造工艺繁琐、复杂，制造成本高吗？
西门子电源模块6SL3100-0BE31-2AB0原装供应
常闭式电磁动紧急切断阀之产品性能及作用原理与结构说明
UV紫外老化箱具备的功能
酶法液化通风回流制醋工艺-食醋酿造发酵
不锈钢反应釜加热冷却控温系统注意事项【山东龙兴集团】电加热不锈钢反应釜、蒸汽不锈钢反应釜
尿素工种项目粉尘、废气洗涤塔用波纹规整填料
户外led显示屏什么牌子好
在操作LT-286G 防护服拒液效率测试仪 前需要注意什么？
人（human）磷酸化tau217蛋白（p-tau217）
elisa检测试剂盒
使用说明书
检测原理
试剂盒采用双抗体一步夹心法酶联免疫吸附试验（elisa）。往预先包被磷酸化tau217蛋白（p-tau217）抗体的包被微孔中，依次加入标本、标准品、hrp标记的检测抗体，经过温育并彻-底洗涤。用底物tmb显色，tmb在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成最终的黄色。颜色的深浅和样品中的磷酸化tau217蛋白（p-tau217）呈正相关。用酶标仪在450nm 波长下测定吸光度（od 值），计算样品浓度。
样品收集、处理及保存方法
1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。
2. 血浆：edta、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。
3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。
4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。
5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。
自备物品
1.酶标仪（450nm）
2.高精度加样器及枪头：0.5-10ul、2-20ul、20-200ul、200-1000ul
3.37℃恒温箱
操作注意事项
1.试剂盒保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完-全溶解后再使用。
2.实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。
3.浓度为0的s0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，最终结果乘以5才是样本实际浓度。
4.严格按照说明书中标明的时间、加液量及顺序进行温育操作。
5.所有液体组分使用前充分摇匀。
试剂盒组成
名称
96孔配置
48孔配置
备注
微孔酶标板
12孔×8条
12孔×4条
无
标准品
0.3ml*6管
0.3ml*6管
无
样本稀释液
6ml
3ml
无
检测抗体-hrp
10ml
5ml
无
20×洗涤缓冲液
25ml
15ml
按说明书进行稀释
底物a
6ml
3ml
无
底物b
6ml
3ml
无
终止液
6ml
3ml
无
封板膜
2张
2张
无
说明书
1份
1份
无
自封袋
1个
1个
无
注：标准品（s0-s5）浓度依次为：0、125、250、500、1000、2000 pg/ml
试剂的准备
20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。
洗板方法
1.手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。
2.自动洗板机：每孔注入洗液350μl，浸泡1min，洗板5次。
操作步骤
1.从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。
2.设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μl；
3.样本孔先加待测样本10μl，再加样本稀释液40μl；空白孔不加
4.除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（hrp）标记的检测抗体100μl，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。
5.弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。
6.每孔加入底物a、b各50μl，37℃避光孵育15min。
7.每孔加入终止液50μl，15min内，在450nm波长处测定各孔的od值。
结果判断
绘制标准曲线：在excel工作表中，以标准品浓度作横坐标，对应od值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。
试剂盒性能
1.准确性：标准品线性回归与预期浓度相关系数r值，大于等于0.9900。
2.灵敏度：最-低检测浓度小于10 pg/ml。
3.特异性：不与其它可溶性结构类似物交叉反应。
4.重复性：板内、板间变异系数均小于15%。
5.贮藏：2-8℃，避光防潮保存。
6.有效期：6个月
免责声明
1.试剂盒仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。
2.严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。
for research use only.
not for use in diagnostic procedures.
humantau(p-tau217)elisa kit instruction
intended use
thisp-tau217elisa kit is intended labohumanory for research use only and is not for use in diagnostic or therapeutic procedures.the stop solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. in order to measure the concenthumanion oftauin the sample, thisp-tau217elisa kit includes a set of calibhumanion standards. the calibhumanion standards are assayed at the same time as the samples and allow the opehumanor to produce a standard curve of optical density versusp-tau217concenthumanion. the concenthumanion ofp-tau217in the samples is then determined by comparing the o.d. of the samples to the standard curve.
samplecollection and storages
serum- use a serum sepahumanor tube and allow samples to clot for 30 minutes before centrifugation for10 minutes at approximately3000×g. remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.avoid repeated freeze-thaw cycles
plasma- collect plasma using edta or heparin as an anticoagulant. centrifuge samples for30minutes at3000×g at 2-8℃ within 30 minutes of collection. store samples at -20℃or -80℃. avoid repeated freeze-thaw cycles.
cell culture supernates and other biological fluids-remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. avoid repeated freeze-thaw cycles.
note: the samples shoule be centrifugated dequately and no hemolysis or granule was allowed.
materials required but not supplied
1. standard microplate reader(450nm)
2. precision pipettes and disposable pipette tips.
3. 37 ℃ incubator
precautions
1.donotsubstitutereagentsfromone kitto another.standard, conjugateandmicroplates arematchedfor optimal performance.useonlythereagentssuppliedbymanufacturer.
2. donotremovemicroplatefromthestorage baguntilneeded.unusedstripsshouldbestored at2-8°cintheir pouchwiththe desiccantprovided.
3.mix all reagents before using.
remove allkitreagentsfromrefrigehumanor and allowthemtoreachroomtempehumanure( 20-25°c)
materials supplied
name
96determinations
48determinations
microelisa stripplate
12*8strips
12*4strips
standard
0.3ml*6tubes
0.3ml*6tubes
sample diluent
6.0ml
3.0ml
hrp-conjugate reagent
10.0ml
5.0ml
20x wash solution
25ml
15ml
chromogen solution a
6.0ml
3.0ml
chromogen solution b
6.0ml
3.0ml
stop solution
6.0ml
3.0ml
closure plate membrane
2
2
user manual
1
1
sealed bags
1
1
note:standard (s0→s5) concenthumanion was followedby:0,125,250,500,1000,2000 pg/ml
reagent prepahumanion
20×wash solution:dilute withdistilled or deionized water1:20.
assay procedure
1.prepare allreagentsbeforestartingassayprocedure.itisrecommendedthatallstandardsand samplesbe addedin duplicatetothemicroelisastripplate.
2.addstandard:set standard wells,testing sample wells.add standard 50μl to standard well.
3. addsample: add testing sample10μlthen add40μlof sample diluentto testing sample well; blank welldoesn’t add anyting.
4. add100μlofhrp-conjugate reagentto each well,cover with anadhesive stripandincubatefor60 minutesat37°c.
5.aspihumane each well and wash, repeating the processfourtimes for a total of fivewashes.wash by filling each well with washsolution(400μl) using a squirt bottle, manifolddispenseror autowasher. complete removal of liquid at each step is essential to goodperformance. after the last wash, remove any remaining washsolutionby aspihumaning ordecanting. invert the plate and blot it against clean paper towels.
6.add chromogen solution a 50μl and chromogen solution b 50μl to each well.gently mixandincubate for 15 minutes at37°c.protect from light.
7.add 50μlstop solution to each well. the color in the wells should change from blue toyellow. if the color in the wells is green or the color change does not
appear uniform,gently tap the plate to ensure thorough mixing.
8readtheopticaldensity(o.d.)at450nmusingamicrotiterplatereaderwithin15minutes.
calculation of results
1.this standard curve is used to determine the amount in an unknown sample. the standard curve is genehumaned by plotting the average o.d. (450 nm) obtained for each of the six standard concenthumanions on the vertical (y) axis versus the corresponding concenthumanion on the horizontal (x) axis.
2.first, calculate the mean o.d. value for each standard and sample. all o.d. values, are subtracted by the mean value of the zero standard before result interpretation. construct the standard curve using graph paper or statistical software.
3.to determine the amount in each sample, first locate the o.d. value on the y-axis and extend a horizontal line to the standard curve. at the point of intersection, draw a vertical line to the x-axis and read the corresponding concenthumanion.
4.any variation in opehumanor, pipetting and washing technique, incubation time or tempehumanure, and kit age can cause variation in result. each user should obtain their own standard curve.
5.the sensitivity by this assay is10 pg/ml
6.standard curve
storage： 2-8℃.
validity：six months.
for research use only; not for therapeutic or diagnostic applications!please read through entire procedure before beginning!
关键词：洗板机 水浴锅 酶标仪 恒温箱
磁性分离器的工作原理及应用
你知道磁阻式转速传感器都有哪些特点吗？
pH传感器探头如何发展的？
液压打包机的总体结构组成
德微光学教你金相显微镜目镜的安装
人磷酸化Tau217蛋白（p-Tau217） ELISA检测试剂盒 使用说明书
汽水分离器技术分析
上海多级离心泵生产厂家讲解卧式多级离心泵的维护保养
巨为盐雾腐蚀试验箱的产品结构
小型口腔门诊污水处理消毒设备
局部放电测试仪工程原理及应用
分离机结构复杂，部件多，制造工艺繁琐、复杂，制造成本高吗？
西门子电源模块6SL3100-0BE31-2AB0原装供应
常闭式电磁动紧急切断阀之产品性能及作用原理与结构说明
UV紫外老化箱具备的功能
酶法液化通风回流制醋工艺-食醋酿造发酵
不锈钢反应釜加热冷却控温系统注意事项【山东龙兴集团】电加热不锈钢反应釜、蒸汽不锈钢反应釜
尿素工种项目粉尘、废气洗涤塔用波纹规整填料
户外led显示屏什么牌子好
在操作LT-286G 防护服拒液效率测试仪 前需要注意什么？